Outdoor storage areas for your hot tub chemicals should be situated away from anything flammable. Keep any petrol-powered equipment, like your lawnmower, in a different location. The storage area should also be away from sources of heat, like an outdoor fire pit or BBQ. ClearWater® is our chosen and recommended chemical provider. Developed with Lay-Z-Spa in mind, the range of ClearWater® hot tub chemicals includes everything needed to make sure your Lay-Z-Spa's water stays safe, clean and clear. Explore the table below which includes each product’s use and function.

For high chlorine levels above 5ppm, we would suggest you drain the Lay-Z-Spa to the minimum mark and re-fill with fresh water to the maximum mark, this will help to dilute the excess chemical. Or, remove the cover from the hot tub to allow evaporation of the chemical (keep the spa filter running constantly). This TA Increaser helps raise Total Alkalinity levels, which in turn will help control pH levels and chlorine. The hot tub and pool test strips highlight, chlorine levels, the water’s pH and Total Alkalinity levels. There are three separate sections on each strip to indicate each individual level. The ClearWater Chemical Measuring Set is a must‑have accessory for all pool and hot tub users and includes 2 measuring jugs, 1 mixing rod and 3 measuring spoons (5ml, 10ml and 50ml) for precise dosage. Do not eat, drink or smoke when using this product. Have a First Aid Kit available for any accidentsThe Clearwater Dip Tests are manufactured by the founders of dip testing in the USA and are the most accurate available on the market so you know you’re getting an accurate reading every single time. Chlorine levels of a hot tub should be 3‑5 ppm (Parts Per Million), pH levels should be 7.2 ‑ 7.6 and Total Alkalinity levels should measure 80 ‑ 120 ppm (Parts Per Million). Clearwater Multifunction Tablets are an effective and hassle-free way of maintaining clear and healthy spa water. They contain a combination of chemicals that act in a number of ways. These slow-release tablets contain chlorine, algaecide and water clarifier. The chemical dispenser slowly releases the mini-tablets into the water, making this a completely hassle-free way of treating your water even for the user with a busy schedule.

Total Alkalinity (TA) is the measure of your hot tub water’s ability to neutralise acids. Balanced Total Alkalinity helps control the pH levels and the correct level to aim for is between 80 and 120 parts per million (ppm). The Clearwater® Dip Tests are manufactured by the founders of dip testing in the USA and are the most accurate available on the market so you know you're getting an accurate reading every single time. In the event of spillage, clean up using clean receptacles and dispose of carefully. Do not add water to spilled materials. Do not use floor sweeping compounds to clean up spills. Sweep and scoop spilled material into clean, dedicated equipment. If you are going away we would suggest emptying the pool and cleaning it so the water is not left to go stagnant. Do no re-fill until you return from your trip.Chlorine is a sanitiser that controls and prevents bacteria growth and is essential for the hot tub water to be clean and safe to use. The recommended Free Chlorine* level in a hot tub is 3-5ppm (parts per million). Not balancing the Total Alkalinity levels in your hot tub can cause a number of issues that can impact your spa experience. Clearwater pH Minus , also known as ‘pH reducer’ is the most simple and effective way to decrease the pH of your spa water when it has surpassed the recommended level. pH minus can also be used to lower TA (Total Alkalinity) levels.

Every attempt should be made to avoid mixing spilled material with other chemicals or debris when cleaning up. Do not attempt to reseal any contaminated drums. Do not transport wet or damp material. Please note: The table is only applicable to Clearwater® Chemicals. Dosages are only approximate and the effect of chemicals on your water can vary each time you use them, depending on the exact amount of water in your hot tub, water type, water temperature, positioning of hot tub etc. Therefore it is essential to test the water every time before you use it. Dip a ClearWater® Test Strip in the centre of your Lay‑Z‑Spa, remove and hold it still for 15 seconds.For low pH levels below 7.2 you will need to use pH Plus to help raise the pH levels and balance the water. Drain hot tub to the minimum mark and re-fill with fresh water to the maximum mark, this will help to dilute the excess chlorine. Clearwater Foam Remover is designed to control and prevent foaming in your hot tub, which is typically caused by the reaction of water with shampoos, deodorants and natural body oils present on the user. For low TA levels below 80ppm you will need to use Total Alkalinity Increaser. The amount of TA + you need to add to your hot tub depends on the volume of water and how low your readings are. As a guide - a hot tub of 1,000 litres requires 18g to raise Total Alkalinity levels by 10ppm (parts per million).

This is an ideal set of hot tub chemicals for beginners as it comes with a user guide with simple, easy-to-follow instructions, dosing guidance, safety tips and problem-solving so you can get confidently get started with hot tub water treatment and maintenance. Clearwater® chemicals are designed for and tested on Lay-Z-Spa hot tubs but can be used on any and all home hot tubs. Chemical water treatment for hot tubs is essential regardless of how long or how often you plan to use the hot tub and this starter kit has everything you need to get started and keep up the water maintenance. Clearwater Clarifier contains flocculants which bind small particles of debris and algae together so that your Lay-Z-Spa filtration system can adequately remove them, resulting in clean and sparkly water. This is a very effective way of preventing your spa water from looking dull and cloudy, due to the build-up of dead algae and debris that is too small to be trapped by your filter. Even if you have treated your spa for algae using Clearwater Algaecide, it is recommended that you use the Water Clarifier to remove any residual debris. Remove cover from pool to allow evaporation of the chemical (keep the pool filter running constantly). Dissolve the quantity of Chlorine Granules in a jug of warm water and pour into your hot tub. Activate the AirJets for a few minutes to circulate the chemicals evenly throughout the water.pH measures how acidic or alkaline your water is and the ideal range for hot tubs is between 7.2 and 7.6. Balanced pH is necessary for other chemicals to work properly and imbalanced pH levels can impact your hot tub components and cause skin irritation. When you’re ready to begin mixing your chemicals, you should handle them with chemical resistant gloves. The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. It is also advised to wear tightly sealed goggles and appropriate protective clothing such as long sleeves, trousers, and closed-toed shoes that fully protect your feet from spills. You should also wash your hands after handling chemicals. Always pre-dissolve chemicals in a clean, plastic container in a well-ventilated area. When pre-dissolving chemicals always add chemicals to water and not vice versa. Always add the chemicals to the water.