M14 (14mm x 40mm) Hex Bolt (Fully Threaded Setscrew) - Steel (Pack of 5)

£9.9
FREE Shipping

M14 (14mm x 40mm) Hex Bolt (Fully Threaded Setscrew) - Steel (Pack of 5)

M14 (14mm x 40mm) Hex Bolt (Fully Threaded Setscrew) - Steel (Pack of 5)

RRP: £99
Price: £9.9
£9.9 FREE Shipping

In stock

We accept the following payment methods

Description

According to EN1993-1-8 § 3.6.1(4) the design shear resistance F v,Rd should only be used where the bolts are used in holes with nominal clearances not exceeding those for normal holes as specified in EN 1090-2 'Requirements for the execution of steel structures'. Ultimate Tensile and Proof loads for metric bolts according ISO 898-1 "Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread". For typical coarse pitch thread bolts the standard sizes are: M3, M3.5, M4, M5, M6, M7, M8, M10, M12, M14, M16, M18, M20, M22, M24, M27, M30, M33, M36, M39. Minimum and maximum spacing p 1, p 2 and edge distances e 1, e 2 for bolts are given in EN1993-1-8 Table 3.3. The minimum values are: e 1≥ 1.2 d 0, e 2≥ 1.2 d 0, p 1≥ 2.2 d 0, p 2≥ 2.4 d 0, where d 0 is the diameter of the hole, e 1, p 1 are measured parallel to the load transfer direction and e 2, p 2 are measured perpendicular to the load transfer direction. The bearing resistance of the bolt F b,Rd should be verified against the applied shear load F v,Ed in accordance with EN1993-1-8 Table 3.4:

Coarse threads are those with larger pitch (fewer threads per axial distance), and fine threads are those with smaller pitch (more threads per axial distance). Coarse threads have a larger threadform relative to screw diameter, whereas fine threads have a smaller threadform relative to screw diameter.

Combined shear and tension

The diameter equal to the external diameter of the threads or the overall diameter of the part. (Nominal diameter is more of a label than a size. For example, a bolt and nut may be described as being ½” diameter. But neither the external threads of the bolt nor the internal threads of the nut are exactly .500 in diameter. In fact, the bolt diameter is a little smaller and the nut diameter a little larger. But it is easier to specify the components by a single size designation since the bolt and nut are mating components.) The tensile stress area depends on the thread and it can be calculated according to ISO 898-1 Section 9.1.6.1.

The interaction between shear and tension is expressed in EN1993-1-8 Table 3.4 according to the following linear relation: For full table with more Property Classes - rotate the screen! Metric Bolts - Fine Threads - Minimum Ultimate Tensile Loads Thread The design shear resistance of bolts F v,Rd as given in EN1993-1-8 Table 3.4 is only valid when the bolt is used in holes with nominal clearance not exceeding the values given in the standard EN 1090-2 'Requirements for the execution of steel structures', as specified in EN1993-1-8 §3.6.1(4). Proof load is defined as the maximum tensile force that can be applied to a bolt that will not result in plastic deformation. A material must remain in its elastic region when loaded up to its proof load typically between 85-95% of the yield strength. Acceptable clamp load is typically 75% of proof load.

In general the stress area of fine pitch thread bolts passing through the threaded part is larger as compared to the coarse pitch thread bolts. Compare the bolts you have with the diagrams below, then refer to the appropriate chart to see the ideal tightening torque. Metric Bolt Torque Chart The resulting hole diameter d 0 for each type of hole (normal, oversize, short slotted, long slotted) is determined by adding the nominal clearance given in EN 1090-2 Table 11 to the nominal diameter d of the bolt. By approximately ignoring the corner rounding for a perfect hexagon the relation of the distance across points s' and the distance across flats s is s' = s / cos(30°) = 1.1547⋅ s. The standard coarse pitch thread metric bolt sizes are: M3, M3.5, M4, M5, M6, M7, M8, M10, M12, M14, M16, M18, M20, M22, M24, M27, M30, M33, M36, M39.

The standarized properties of metric bolts are specified in the international standard ISO 898-1:2009 'Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread'.where e 2 is the distance between the center of the edge bolt and the end of the plate measured perpendicular to the load transfer direction, p 2 is the distance between the centers of neighboring bolts measured perpendicular to the load transfer direction, and d 0 is the diameter of the bolt hole.



  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns

Fruugo

Address: UK
All products: Visit Fruugo Shop